Zanussi Dryer Error Codes

Here are the tables containing Zanussi dryer error codes. Each code is a signal of a problem with Zanussi dryer which needs a solution, often an immediate one. For each of the codes there are detailed descriptions and possible actions recommended.

There are lists of possible problems and error codes for several different dryer models of this company. Here you can find IZTE 135, Series 51, TCS 674 E and some other models error codes. As the issues described may be serious and related to power supply, or may need spare parts replacement, do not try to fix them by yourself. It is better to address to the specialists.

Zanussi IZTE 135 Dryer Error Codes

Code Description / Solution
E10 indicate that the problem lies with the filling of the machine and the machine is not happy with the filling
E11 blocked or trapped pipe or a problem with the valves
E12problem with the pressure switch or a blocked pressure switch hose
E21 problem lies with the draining of the machine
E22 check the filter and the pump
E23 block to pump
E24broken control
E30 E31problem in the door lock
E33 E37problem with the sensors
E40 - E45errors relates to the door lock and its control by the board
E50 - E62errors relate to the motor
check the motor is spinning
check the brushes if fitted
check over the plugs and wires to the motor
E61 E62 heater problems
E66stuck heater relay problems
E71relates to the water temperature sensor

Zanussi Series 51 New Dryer Error Codes

Code Description / Solution
E00No alarm.
E21 Canister fill pump triac faulty. Possible fault Wiring faulty; Electronic board faulty. Cycle interrupted. OFF
E22Triac "sensing" circuit for the canister fill pump faulty Possible fault Electronic board faulty. Cycle interrupted. Machine Status/Action OFF
E31Conductimetric sensor signal frequency too high. Possible fault Electronic board faulty.Machine Status/Action Alarm activated only during diagnostics.
E32Conductimetric sensor signal frequency too low. Possible fault  Wiring faulty; Brushes worn/faulty; Electronic board faulty. Machine Status/Action  Cycle interrupted.
E33It is displayed in the last alarm, if position 8 is NOT OK. Possible fault Wiring faulty; Brushes worn/faulty; Electronic board faulty.  Machine Status/Action Alarm activated only during diagnostics.
E45Door closure sensor. Possible fault Door interlock faulty; Wiring faulty; Electronic board faulty. Machine Status/Action Cycle interrupted.
E51Motor power triac short-circuited. Possible fault Motor faulty; Wiring faulty; Electronic board faulty. Machine Status/Action Cycle interrupted.
E52Intervention of motor overheating safety cut-out. Possible fault Motor faulty; Intervention of motor overheating cutout; Wiring faulty; Electronic board faulty. Machine Status/Action Power to the heater unit and reversal of the direction of rotation are interrupted. If the problem does not re-occur, the alarm is memorized and the cycle continues. If the fault persists after several attempts to supply power (about 35 min.), alarm E51 is generated.
E53Motor triac "sensing" circuit faulty. Possible fault Electronic board faulty. Machine Status/Action Cycle interrupted.
E54Motor in-operational. Possible fault Excessive wash load; Voltage too low; Motor/transmission system inoperative. Machine Status/Action Cycle paused after several attempts at powering the motor. Start
E61Insufficient heating (maximum time exceeded). Possible fault  Heater unit faulty; Wiring faulty; NTC sensor incorrectly calibrated/out of position; Electronic board faulty. Machine Status/Action Cycle paused.
E62Power relay to heater unit faulty. Possible fault Heater unit faulty; Wiring faulty; Electronic board faulty. Machine Status/Action Forced cooling cycle.
E63Intervention of auto-reset thermostat on the heater unit. Possible fault Thermostat faulty (replace heater unit); Heater unit faulty; Wiring faulty; Electronic board faulty. Machine Status/Action Disconnects the power supply to the heater unit. If the problem does not re-occur, the alarm is memorized and the cycle continues. If, after several attempts to restore power, the fault persists, alarm E62 is generated.
E64Heater thermostat. Possible fault Heater thermostat faulty: Wiring faulty; Electronic board faulty.
E65Fan motor triac faulty. Possible fault Fan motor wiring not connected; Motor faulty; Triac interrupted.
E66Fan motor thermal protection. Possible fault Fan motor wiring not connected; Motor faulty; Triac interrupted.
E67Triac control faulty. Possible fault Fan motor wiring not connected; CRM board faulty.
E71NTC1 sensor faulty. Possible fault NTC1 sensor faulty; Wiring faulty; Electronic board faulty. Machine Status/Action Forced cooling cycle.
E72NTC2 sensor faulty. Possible fault NTC2 sensor faulty; Wiring faulty; Electronic board faulty.
E82Selector in OFF position faulty. Possible fault Board wiring; board faulty.
E83Selector positions wrong. Possible fault Board wiring; board faulty.
E93Error in the configuration of the appliance. Possible fault EEPROM configuration incorrect. Electronic board faulty. Cycle interrupted. OFF
E94Error in the configuration of the drying cycle. EEPROM configuration incorrect. Possible fault Electronic board faulty. Machine Status/Action Cycle interrupted.
E97Incongruence between selector and cycles. Possible fault Configuration error. Machine Status/Action Cycle interrupted.

Zanussi TCS 674 E Dryer Error Codes

Code Description / Solution
EA1CRM board communication faulty. Possible fault  Board wiring; CRM board faulty.
EA2CRM board protocol inconsistent. Possible fault Software wrong; CRM board faulty.
EA3Board selector faulty. Possible fault Electronic board faulty.
EA4Selector protocol wrong. Electronic board faulty.
EB1Power frequency to appliance out of limits. Possible fault Problems with the power supply (incorrect/interference). Electronic board faulty. Machine Status/Action  Cycle interrupted. If a stable power supply is restored before the time-out has elapsed, the cycle resumes.
EB2Power voltage too high. Possible fault Problems with the power supply (incorrect/interference). Electronic board faulty. Machine Status/Action Cycle interrupted
EB3Power voltage too low. Possible fault Problems with the power supply (incorrect/interference). Electronic board faulty. Machine Status/Action Cycle interrupted. If a stable power supply is restored before the time-out has elapsed, the cycle resumes.
EC1Voltage incongruence between boards. Possible fault Problems with the power supply (incorrect/interference). CRM board faulty.
EC2Frequency incongruence between boards. Possible fault Problems with the power supply (incorrect/interference). CRM board faulty.
EC3CRM resistance out of time (only in diagnostic mode). Possible fault CRM group not connected; CRM group faulty.
EC4Steam generator (CRM) heater relay. Possible fault CRM group not connected; relay on board faulty.
EC5CRM thermostat faulty. Possible fault CRM group not connected; CRM group faulty.
EC6CRM piloting faulty. Possible fault CRM board faulty.
EC7CRM pump triac. Possible fault Pump wiring not connected; pump faulty; Triac faulty.
EC8CRM pump diode. Possible fault Diode on wiring short-circuited.
EC9CRM pump piloting faulty. CRM board faulty.
ECAWater tank empty. Possible fault Tank level sensor wiring; tank level sensor faulty; water tube obstructed.

Zanussi ZDC 46130 W Dryer Error Codes

Error codeCause
Error code E40** is displayed in the display windows- the cover is not correctly closed.
Error code E20** is displayed in the display windows- the drain filter is blocked,
- the drain pipe is blocked or kinked,
- the drain pipe istoo high
- the drain pump is blocked,
- the installation siphon is blocked.
Error code E10** is displayed in the display windows- the water tap is closed,
- the water network has been cut off.
Error code EAO** is displayed in the display windows- the flap s of the drum door are opened.

E51, E52, E53 & E54 Tumble dryer error code Zanussi