Wascomat Dryer Error Codes

Troubleshooting may sound difficult for many people, so there are lists of Wascomat dryer error codes of different models available. If you see a sign on the display, you can address these tables and understand what is going wrong with your Wascomat dryer.

There are many different breakdowns happening to dryers. Codes let you know what is the issue, and the repair actions should be performed based on this information. You can understand, for example, if the problem happened because of the sensor or the pump.

As there are many breakdowns which may need spare parts replacement, do not do the repair by yourself. It is better to address to specialists for that.

Wascomat TD3030 Dryer Error Codes

CODEDESCRIPTION
E01Inlet Too Hot
E02Outlet Too Hot / Software Error
E03Inlet Sensor Short
E04Outlet Sensor Short
E05Motor 1 Overheat
E06Motor 2 Overheat
E07Option Failure
E08Inlet or Outlet Too Hot
E09Lint Drawer Open
E10Programming Error
E11Drying Error RMC Excessive Time
E12Drying Error Autostop Excessive Time
E13Drying Error CP Excessive Time
E14Gas Error
E15Vacuum (Sail) Switch Does Not Close
E16Vacuum (Sail) Switch Stuck Closed
E17Inlet Sensor Open
E18Outlet Sensor Open
E98Unknown Sensor Error
E99Communication Error

Wascomat 032921GB Dryer Error Codes

CodeDescription
E 01Inlet air (electric heated dryer only) - input temperature is too high
The temperature of the air entering the drum is too high (measured by thermistor element).
Inlet air (gas heated dryer only) - input temperature is too high
The temperature of the air entering the drum is too high (measured by thermistor element).
E 02Outlet air - Output temperature is too high
The temperature of the air leaving the drum is too high (measured by thermistor element).
E 03Inlet air - Sensor has short-circuited
The thermistor element measuring the air inlet temperature to the drum, or the wiring to the sensor has shorted.
E 04Outlet air - Sensor has short-circuited
The thermistor element measuring the air outlet temperature from the drum, or the wiring to the sensor has shorted.
E 05Blower motor -The thermal protection switch in the motor, or its harness, is open.
E 06Drum motor - The thermal protection switch in the motor, or its harness, is open.
E 09Not in use on this model.
E 10Setting - Programming error / incorrect or missing parameter(s).
E 11Not in use on this model
E 12Drying error - Maximum allowable Autostop time exceeded (non-coin operated models only)
E 13Drying error - Requested drying time is longer than maximum allowed, (dryer connected to a payment system)
E 14Gas error - A flame was not detected on gas heated dryers
E 15Vacuum switch
The vacuum switch does not shut within 5 seconds after the dryer is started. E 15 check list
E 16Vacuum switch
The vacuum switch was already closed when an attempt to start the dryer was made.
E 17Input sensor disconnected
The inlet thermistor or wiring to the thermistor is open.
E 18Output sensor disconnected
The outlet thermistor or wiring to the thermistor is open.
E 99Communication error
The user module does not receive communication from the main board, (user module and main board).

Wascomat Selecta II Dryer Error Codes

Error codeDescription
E 19Not in use
E 20Machine is out of operation
The tumble dryer has been deactivated by the PC software.
E 21Network error, no polling CMIS
The computer has not called the tumble dryer during the timeout period.
E 22Network error, no polling CBT
The computer has not called the tumble dryer during the timeout period.
E 23Not in use
E 24Condensate container is full
The condensate container is full and the pump is not operating.
E 25Damper output air is not closed correct
(Applies only to Clean Room tumble dryers).
E 26Damper output air is not open correct
(Applies only to Clean Room tumble dryers).
E27Hepa filter pressure warning
(Applies only to Clean Room tumble dryers).
E 28Input temperature oscillating
Close