Indesit Washer Dryer Error Codes

Indesit dryer problems isn’t considered to be the frequent problem among the users of this brand. At the same time as everybody knows, it’s better to be ready to face anything. In case you experience a problem, use the guide given here. In such case you won’t be afraid of Indesit tumble dryer repairs.

Indesit AQUALTIS AQM8D Washer Dryer Error Codes

DisplayFault CodeFault
Light 4F01Motor triac
Light 3F02Motor jammed/tacho
Lights 3+4F03NTC faulty
Light 2F04Pressure switch stuck on empty
Lights 2+4F05Pressure switch stuck on full
Lights 2+3F06N/A
Lights 2+3+4F07Heater relay
Light 1F08Heater relay
Lights 1+4F09Eprom/set up error
Lights 1+3F10Pressure switch not sensing
Lights 1+3+4F11Pump/drain error
Lights 1+2F12Communication error
Lights 1+2+4F13Dryer ntc/fan motor
Lights 1+2+3F14Dryer heater
Lights 1+2+3+4F15Dryer heater relay
Light 4F17Door lock
Light 3F18Comms error-power board

Indesit GB IWDD 7123 Washer Dryer Error Codes

Code IssueSolution
F01Washing machine is not operating – some or all functions are not selectableDisconnect (unplug) the appliance from the mains supply for a minimum of 2 minutes. Reconnect supply and wait 30 seconds and try starting the machine again
F02Intermittent or no drum rotation during wash cycle
F03Temperature sensing faultWashing machine not heating on wash or dry settings
F05Washing machine door will not open / the door can be opened but water remains inside the drumPlease check for blockages in your pump filter
Also check for any blockages in waste water hose and in any under-sink plumbing. If none of the above solutions work, it is likely you have a pump failure and will need further assistance.
F06Washing machine door cannot be opened or closed / when the door is closed the machine the programme will not startIf your washing machine door will not close, please check for any obstructions in the door lock. If the problem persists,
F07During a wash cycle the programme pauses part way through / the machine is not heating and the pump runs continuouslyPlease arrange an engineer visit
F08During a wash cycle the programme pauses part way throughPlease arrange an engineer visit
F09Washing machine isn’t operating multiple flashing lights and/or display. Unable to select a programmePlease arrange an engineer visit
F11Water remains in washing machine / not pumping outPlease arrange an engineer visit
F16Drum lock position sensor faultWashing machine drum is stopping in the wrong position or is not locked in the correct position
F18Some or all display / functions do not work on my washing machinePlease disconnect (unplug) the appliance from the mains supply for a minimum of 2 minutes. Reconnect supply, wait 30 seconds and try starting the machine again

Indesit PWDE 7125 W Washer Dryer Error Codes

Code Description / Solution
F01Short circuit in the control circuit of the CM drive motor
Check the contact strip of the drive motor (a possible cause of the problem is the chemical corrosion of its contacts).
Replace the electronic module of the washing machine.
F02The drive motor does not work, the tachogenerator circuit is short-circuited or in the break
Check whether the motor is mechanically blocked.
Check the reliability of the terminals on the J9 connector of the electronic module.
Check the electrical resistance of the sensor (about 115 ... 170 0m).
The resistance is measured between pins 1 and 2 of connector J9. In the event of a short circuit in this circuit, disconnect connector J9 and check the wires from the side of the sensor. If an induction motor is installed in the CM, make sure the electrical connection of terminals 6 and 7 of the J9 connector to the sensor is secure.
Replace the motor.
Replace the electronic module.
F03The NTC temperature sensor circuit is closed, either in the open circuit or "stuck" in the TEN relay
Check the reliability of the J8 connector.
Check the temperature sensor, considering that its resistance at room temperature (20 ° C) is 20 kOhm (can be measured at terminals 11 and 12 of connector J8). If the result is different, check the integrity of the wiring from the module to the sensor.
Replace the NTC temperature sensor.
Replace the electronic module.
F04The water level sensor simultaneously generates the signals "EMPTY TANK" and "FREQUENCY"
The reason for this defect is that the sensor is "filled" with the contact group "EMPTY TANK", in this case the CM pours the water to the overflow level. When this level is reached, the drain pump is automatically turned on.
Check the connection quality of J3 connector on the electronic module.
Replace the level sensor.
Replace the electronic module.
F05The drain pump is blocked (does not work) or the level sensor generates a signal EMPTY TANK after the completion of the water draining procedure
Check the connections at J9. At the time of the intended operation of the pump, it is possible to check the presence between contacts 8,9 of the J9 connector of the alternating voltage of 220 V.
Check the filter and drain hose.
Replace the drain pump.
Replace the electronic module.
F06Button Error
The code is displayed in the SM of the Ariston Dialogic family (AD series)
Check for the presence of a contact in the connectors and harnesses between the controller and the control panel.
Check the serviceability of the buttons on the control panel.
Successively replace the control panel and electronic controller.
F07After completing the water fill operation, the level sensor does not remove the signal "EMPTY TANK"
If there is no water in the tank after the operation of water filling, no power is supplied to the heater.
This is a protective function, since without water the heater can burn out
Check for water in the water supply or water pressure is too low.
Check the water inlet valve.
Check the blockage in the water filling system.
Check the water level sensor (pressure switch).
After filling the water (if any), the contact group "EMPTY TANK" of the level sensor must be open. Its status is monitored, for example, on pins 2 and 3 of the J3 connector of the electronic module. Otherwise, the level sensor and the electronic module are successively replaced.

Indesit WE12UK Washer Dryer Error Codes

On/Off LED FlashesFaultActions
1Motor faultCheck connections
Motor
Main PCB.
2Motor faultCheck
Tacho
Motor harness.
3ThermistorCheck thermistor (20K).
4Pressure SwitchJammed on empty.
5Pressure SwitchJammed on full
Blocked/Faulty Pump.
6Programme Selector – management errorCheck connections
Programme Selector
Main PCB.
7Heater RelayCheck heater (1800W approx 32.)
8Heater RelayCheck connections
Heater
Pressure switch
Module Replace Main PCB & E-prom.
9Incompatible E-promReplace Main PCB and E-prom
If new module has been fitted ensure that E-prom has been fitted correctly. Match up D-cut on surface of E-prom with module.
10Pressure SwitchCheck connections
Pressure switch to ModuleReplace Pressure switch, Main PCB and E-prom.
11PumpCheck pump and connections.
12Communication Error between Main PCB and LCD Display PCBReplace Both Main PCB and LCD Display PCB, including relevantE-proms.
13Dryer Fan does not workCheck connections
Dryer thermistor
Fan Motor
Main PCB.
14Dryer Element faultyCheck connections
Element
Main PCB.
15Dryer Element Relay faultyCheck connections
Main PCB
Pressure switch
Replace Main PCB and E-prom.
NoneDoor is locked but appliance fails to startCheck Connections
Replace Motor.

Indesit IWB5113 Washer Dryer Error Codes

Code Description / Solution
F10No cold fill. Check that the taps are on or if the drain hoses are kinked
F11No hot fill. The ambient temperature is likely to be below freezing possibly due to the pipes being frozen. Also check that the taps are on or if the drain hoses are kinked
F12No mixed fill. It is likely that the water is not turned on at the taps
F13Check the water supply, inlet valve and hot and cold hose connections
F14A fault with the water heating has occurred
F15Water is not being pumped out and a flood condition could occur. Check that the drainage hose is raised to the recommended minimum height and that the pipe is not blocked
F16Extremely high water level Disconnect or turn off the water supply and ensure that the water level does not rise any more
F17Door not closed properly. Close door firmly at the 3 o’clock position
F20The thermistor resistance has drifted or the temperature scanning sequence is incorrect. The ambient temperature could be below freezing
F30/31A motor drive problem has occurred. Try running the programme again
F40Water below protection level during a heat step
F41Water level detect sequence incorrect
F50/51Customer language and wash programme have not been saved