Beko Dryer Troubleshooting

Your favourite Beko dryer is not heating up. What will you do in such situation? First, think about the problem and examine the dryer to get the idea what exactly is happening there. When you made some sort of examination, you can get closer to the problem. Its description can be found in the guide we give here. Read it carefully and you will get the clearest info.

Beko DV 6120 X Dryer Troubleshooting

Problem Solution
Drying process takes too much time• Meshes of the filter may be clogged. Wash with water.
Laundry comes out wet at the end of drying.
• Excessive laundry might have been loaded in. Do not load the dryer in excess.
Dryer does not switch on or the programme does not start. Dryer is not activated when set.• It might have not been plugged in. Make sure that the machine is plugged in.
• The loading door may be ajar. Make sure that the loading door is properly closed.
• Programme might have not been set or the "Start/Pause/Cancel" button might have not been pressed. Make sure that the programme has been set and it is not in “Pause" mode.
• "Childproof lock" might have been activated. Deactivate the childproof lock.
Programme has been interrupted without any cause.• The loading door may be ajar. Make sure that the loading door is properly closed.
• Electricity may be cut off. Press "Start/Pause/Cancel" button to start the programme.
Laundry has shrunk, become felted or deteriorated.• A programme suitable for the laundry type might have not been used. Dry only the laundry which is suitable for drying in dryer after checking the labels on your clothes.
• Select a programme with suitable low temperature for the laundry type to dry your clothes.
Drum lightning does not come on.• Dryer might have not been started by using the "On/Off“ button. Make sure that the dryer is on.
• Bulb may have blown. Call the authorized service to replace the bulb.
“Final / Anti-creasing" symbol flashes.• The 2-hour anti creasing programme to prevent laundry from creasing might have been activated. Turn off the dryer and take out the laundry.
“Final / Anti-creasing" symbol is on.• Programme has come to an end. Turn off the dryer and take out the laundry.
Water comes out the cover.• Clean the entire inner surface of the cover and door gasket.
Cover opens spontaneously.• Push it until you hear that it is closed.
"Water tank" warning symbol is on.• Water may be full.
• Anti-creasing programme might be running. Drain the water in the tank.
“Filter cleaning" symbol is on.• Filter might have not been cleaned. Clean the cover filter.
“Condenser cleaning" symbol is on.• Filter drawer/Condenser might have not been cleaned. Clean the filters in the condenser/filter drawer under the kick plate.

Beko DPY 7405 GXB2 Dryer Troubleshooting

Problem Cause Solution
Is there an error message on the display?The error message can be a code on the display, a flashing LED or a sequence of beeps
Is the ambient temperature between 5°C and 35°C?If the ambient temperature is too low or too high, the tumble dryer may not operate correctlyPlace the dryer in a room which has a suitable temperature.
If the dryer is located in a room, make sure that the temperature of the room is between 5°C and 35°C.
If the room temperature is not within this range, the tumble dryer may not operate correctly and will not heat up.
Heat the room in which the tumble dryer is situated until it reaches a suitable temperature, or move the dryer to another room which is at a suitable temperature
Did you select a steam cycle on your tumble dryer?The steam cycle was selectedIf you select a steam cycle on the tumble dryer, there will be a certain amount of steam inside the dryer’s drum.
When the cycle is finished, there is condensation water inside the tumble dryer.
This is perfectly normal when you use a steam cycle
Is the load too much?Overloading the product can reduce the heat circulation around the clothingRedistribute the load and restart the drying cycle.
If the load is too much, remove some of the clothing from the machine and restart the drying cycle
Are the filters clean? Is the machine clean?If the filters, condenser and/or heat exchanger are dirty, it may be the reason why the machine is not heating up
The filters may appear clean but still be blockedYou can check the filters by holding them up against the light or under a tap and seeing whether the water can flow through them.
If no water passes through the filters, clean them and check them again.
If water will still not pass through the filters, replace them

Beko RA 1300-4400 ecoDryer Troubleshooting

SYMPTOMPOSSIBLE CAUSE - SUGGESTED ACTION
The dryer doesn't start.Verify that the system is powered.
Verify the electric wiring.
The compressor doesn’t work.Activation of the compressor internal thermal protection - wait for 30 minutes, then retry.
Verify the electric wiring.
Where installed - Replace the internal thermal protection and/or the start-up relay and/or the start-up capacitor and/or the working capacitor.
Where installed - The pressure switch PA has been activated
Where installed - The pressure switch PB has been activated
Where installed- The safety thermo-switch TS has been activated
If the compressor still doesn’t work, replace it.
The fan of the condenser doesn’t work.Verify the electric wiring.
PV pressure switch is faulty - replace it.
There is a leak in the refrigerating fluid circuit - contact a refrigeration engineer.
If the fan still doesn’t work, replace it.
DRYPOINT RA HT 75-350 NA – The Aftercooler fan doesn’t work.Verify the electric wiring.
If the fan still doesn’t work, replace it.
DewPoint too high.The dryer doesn't start
The T1 DewPoint probe doesn’t correctly detect the temperature - ensure the sensor is pushed into the bottom of copper tube immersion well.
The refrigerating compressor doesn’t work
The ambient temperature is too high or the room aeration is insufficient - provide proper ventilation.
The inlet air is too hot - restore the nominal conditions.
The inlet air pressure is too low - restore the nominal conditions.
The inlet air flow rate is higher than the rate of the dryer - reduce the flow rate - restore the normal conditions.
The condenser is dirty - clean it.
The aftercooler is dirty - clean it.
The condenser fan doesn’t work
The aftercooler fan doesn’t work
The dryer doesn’t drain the condensate
The hot gas by-pass valve is out of setting - contact a refrigeration engineer to restore the nominal setting.
There is a leak in the refrigerating fluid circuit - contact a refrigeration engineer.
DewPoint too low.The fan is always ON - PV pressure switch is faulty - replace it.
The Hot Gas By-pass Valve is out of setting - contact a refrigeration engineer to restore the nominal setting.
Ambient temperature is too low - restore de nominal condition.
Excessive pressure drop within the dryer.The Pre-Filter (1 micron) is clogged - replace the filter element (cartridge)
The dryer doesn’t drain the condensate
The DewPoint is too low - the condensate is frost and blocks the air
Check for throttling the flexible connection hoses.
The dryer doesn’t drain the condensate.The condensate drain service valve is closed - open it.
Verify the electric wiring.
The DewPoint is too low - the condensate is frozen
Bekomat drainer is not operating correctly
Water within the line.The dryer doesn’t start
Where installed - Untreated air flows through the by-pass unit - close the by-pass.
The dryer doesn’t drain the condensate
DewPoint too high