Ariston washer dryer troubleshooting

Ariston BHWD washer dryer troubleshooting

Problem:Possible causes / Solutions:
The washer-dryer does not switch on.• The appliance is not plugged into the socket fully, or is not making contact.
• There is no power in the house.
The wash cycle does not start.• The washer-dryer door is not closed properly.
• The ON/OFF button has not been pressed.
• The START/PAUSE button has not been pressed.
• The water tap has not been opened.
• A delayed start has been set
The washer-dryer does not take in water (the indicator light for the first wash cycle stage flashes rapidly).• The water inlet hose is not connected to the tap.
• The hose is bent.
• The water tap has not been opened.
• There is no water supply in the house.
• The pressure is too low.
• The START/PAUSE button has not been pressed.
The washer-dryer continuously takes in and drains water.• The drain hose is not fitted at a height between 65 and 100 cm from the flc
• The free end of the hose is under water
• The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch the appliance off and contact the Assistance Service. If the dwelling is on one the upper floors of a building, there may be problems relating to water drain causing the washer-dryer to fill with water and drain continuously. Special anl draining valves are available in shops and help to avoid this inconvenience.
The washer-dryer does not drain or spin.• The wash cycle does not include draining: some wash cycles require the phase to be started manually.
• The drain hose is bent
• The drainage duct is clogged.
The washer-dryer vibrates a lot during the spin cycle.• The drum was not unlocked correctly during installation
• The washer-dryer is not level
• The washer is trapped between cabinets and walls
The washer-dryer leaks.• The water inlet hose is not screwed on properly
• The detergent dispenser drawer is blocked
• The drain hose is not fixed property
The START/PAUSE indicator light (orange) and the function indicator lights flash rapidly.• Switch off the machine and unplug it, wait for approximately 1 minute and switch it back on again.
If the problem persists, contact the Technical Assistance Service.
There is too much foam.• The detergent is not suitable for machine washing
• Too much detergent was used.
The washer-dryer does not dry.• The appliance is not plugged into the socket, or not enough to make contact.
• There has been a power failure.
• The appliance door is not shut properly.
• A delayed start has been set. w
• The DRYING knob is on the setting.

Ariston AML 119 washer dryer troubleshooting

ProblemPossible causes/Solution:
The Washer-dryer won't start.• The appliance is not plugged into the socket, or not enough to make contact.
• There has been a power failure.
The wash cycle won't start.• The appliance door is not shut properly.
• The (ON) button has not been pressed.
• The START/RESET button has not been pressed.
• The water tap is not turned on.
• A delayed start has been set
The Washer-dryer fails to load water.• The water inlet hose is not connected to the tap.
• The hose is bent.
• The water tap is not turned on.
• There is a water shortage.
• The water pressure is insufficient.
• The START/RESET button has not been pressed.
The Washer-dryer continuously loads and unloads water.• The drain hose is not fitted between 65 and 100 cm from the floor
• The free end of the hose is underwater
• The wall drainage system doesn't have a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch the appliance off and call for Assistance. If the dwelling is on one of the upper floors of a building, there may be drain trap problems causing the Washer-dryer to load and unload water continuously. In order to avoid such an inconvenience, special anti-drain trap valves are available in shops.
The Washer-dryer does not drain or spin.• The programme does not foresee the draining: some programmes require enabling the draining manually
• The Anti-crease option is enabled: to complete the programme, press the START/RESET button
• The drain hose is bent
• The drain duct is clogged.
The Washer-dryer vibrates too much during the spin cycle.• The drum was not unblocked correctly during installation
• The Washer-dryer is not level
• The Washer-dryer is closed in between furniture cabinets and the wall
The Washer-dryer leaks.The water inlet hose is not screwed on correctly
The detergent dispenser is obstructed
The drain hose is not secured properly
The ON-OFF/DOOR LOCK Led flashes rapidly at the same time as at least one other LED.Call for Assistance because this means there is an abnormality.
There is too much foam.The detergent is not suitable for machine washing (it should bear the definition "for Washing-machinr" or "hand and machine wash", or the Ike). You used too much detergent.
The washer-dryer does not dry.The appliance is not plugged into the socket, or not enough to make contact
There has been a power failure.
The appliance door is not shut properly.
A delayed start has been set